What’s in the box:
- Amplifier
- Birth sheet with tested power
- Mounting Screw Kit
- Warning Instruction
- Warranty
- Owner’s manual
Features:
- Rockville KRYPTON MT1 1600w Peak/400w Dyno-Certified RMS 2 Channel Marine/Boat Amplifier w Volt Meter
- Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc)
- 2 Ohm: 200 Watts x 2 Channel <1% THD+N
- 4 Ohm: 120 Watts x 2 Channel <1% THD+N
- 4 Ohm Bridged: 400 Watts x 1 Channel
- Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc)
- 2 Ohm: 800 Watts x 2 Channel
- 4 Ohm: 480 Watts x 2 Channel
- 4 Ohm Bridged: 1600 Watts x 1 Channel
- Painted Conformal Coated PCB Board (Uses 2577 Waterproof Glue)
- Rustproof Aluminum heat sink with black hairline finish
- Stainless steel end panels are rustproof
- All screws and mounting hardware are stainless steel and rustproof
- Bottom panel is aluminum and rustproof
- Digital Voltage Display on Amp
- High Level Input(Auto ON)
- High-Speed MOSFET Power Supply
- Under Voltage Protection at 10V
- Over Voltage Protection at 16V
- Tertiary Supplies Circuitry
- Studio-Grade Bipolar Output Stage Transistors
- Fully Adjustable 12dB / Octave Crossover with Differential Circuitry
- Low Pass Filter: 50Hz – 250Hz
- High Pass Filter: 60Hz -1.2KHz
- Full IC-Controlled Protection Circuitry
- Fully Adjustable 12dB Bass Equalizer
- Mute and Delay Soft Start System
- RCA Line Output
- 8 Volt Preamp Circuitry
- Status Mode LED Indicator
- Minimum THD at Rated Power: < 0.05%
- S / N Ratio: >90dB
- Frequency Response: 10Hz – 50KHz
- Damping Factor: >100 @ 100Hz
- 25 Amp x2 ATC Fuse
- Dimensions: (Lx W x H) 12.4″” x 8.7″” x 2.2″”
- What’s in the box: Amplifier. Birth sheet with tested power. Mounting Screw Kit. Warning Instruction. Warranty. Owner’s manual
- Features: Rockville KRYPTON MT1 1600w Peak/400w Dyno-Certified RMS 2 Channel Marine/Boat Amplifier w Volt Meter. Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc). 2 Ohm: 200 Watts x 2 Channel <1% THD+N. 4 Ohm: 120 Watts x 2 Channel <1% THD+N. 4 Ohm Bridged: 400 Watts x 1 Channel.
- Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc). 2 Ohm: 800 Watts x 2 Channel. 4 Ohm: 480 Watts x 2 Channel. 4 Ohm Bridged: 1600 Watts x 1 Channel. Painted Conformal Coated PCB Board (Uses 2577 Waterproof Glue). Rustproof Aluminum heat sink with black hairline finish. Stainless steel end panels are rustproof. All screws and mounting hardware are stainless steel and rustproof.
- Bottom panel is aluminum and rustproof. Digital Voltage Display on Amp. High Level Input(Auto ON). High-Speed MOSFET Power Supply. Under Voltage Protection at 10V. Over Voltage Protection at 16V. Tertiary Supplies Circuitry. Studio-Grade Bipolar Output Stage Transistors. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Low Pass Filter: 50Hz – 250Hz. High Pass Filter: 60Hz -1.2KHz. Full IC-Controlled Protection Circuitry.
- Fully Adjustable 12dB Bass Equalizer. Mute and Delay Soft Start System. RCA Line Output. 8 Volt Preamp Circuitry. Status Mode LED Indicator. Minimum THD at Rated Power: < 0.05%. S / N Ratio: >90dB. Frequency Response: 10Hz – 50KHz. Damping Factor: >100 @ 100Hz. 25 Amp x2 ATC Fuse. Dimensions: (Lx W x H) 12.4˝ x 8.7˝ x 2.2˝
