The latest BST200 12 Volt Automotive Battery Analyzer from ANCEL is dedicatedly developed to test 12V regular flooded, AGM flat plate, AGM spiral and gel batteries. It provides a quick, easy and affordable solution for technicians to view battery charging status, check battery health and detect faults.
🚩A Must for You
ANCEL BST200 is a12V car battery tester, can gives you the basic battery parameters such as voltage, internal resistance, battery health and charge status. Additionally, BST200 will also show you professional advice whether to replace or charge the battery, it a basic but useful car tool for private car owner.
✔️Battery Test
BST200 12 Volt Automotive Battery Analyzer allows you to analyze the battery healthy status and view battery charging status.
✔️Support Multi-Language
Testing standards include currently the world’s majority of battery standards, CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, GB
✔️ANCEL BST200 Car Battery Tester Application
Testing standards include currently the world’s majority of battery standards, CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, GB
✔️ANCEL BST200 Battery Tester Function
Battery Tester Range: from 100 to 1100CCA
⏩How to connect the tester
1. Clean the battery posts or side terminals.
2. Connect the red clamp to the positive (+) terminal and the black clamp to the negative (-)
terminal.
3. Rock the clamps back and forth to make sure the clamps are firmly connected.
4. When the tester is correctly connected, it boots up automatically and shows the voltage of the battery.
NOTE:
📌Do not connect the tester to a voltage source greater than 18V DC; otherwise you may damage the tester.
📌If you are testing inside a vehicle, make sure all accessory loads are cut off, the key is not in the ON position and the doors are closed.
ANCEL PB100 power scan kit is the most revolutionary circuit tester to date, featuring AVOmeter, test light , built -in flashlight , short circuit indicator, relay/component tester, continuity tester and bad groud indicator, the power scan is truly the ultimate in power and affordablity, allowing users to check circuitry in one single step.
🌈ANCEL PB100 Product Properties
– DC voltage range: 0-65V; Resistance range: 0-100 kΩ; Rated current: 1-10 amps; Frequency response of sound passage: 0Hz to 10Khz.
– Perform current injection, measurement, ground test, polarity test, continuity test and component activation.
– Ergonomic housing design with waterproof, rugged, blow-molded housing, easy to handle and store.
– There are 4 modes to diagnose the electrical systems.(DC voltage, AC voltage, Resistance, Diode)
– AC- RMS, AC peak to peak, frequency and pulse width for signal testing.
– High voltage capability: displays up to 60 volts, 0.1 volt resolution.
– 8-amp circuit breaker, automatic reset, no button to press.
– Three additional modes: MIN / MAX / audible monitoring.
– Automatically detects positive, negative and open circuit.
– Large color screen LCD with easy to navigate user menu.
– Comes with an additional 20ft extension cable.
– Find shorts to ground and to voltage.
🔍ANCEL PB100 Functions
1. Find The Short Circuits:In most cases, a short circuit will appear as a blown fuse or a tripping of an electrical protection device.Use the probe tip to activate and energize each of the fuse contacts..The contact which trips the circuit breaker is the shorted circuit.
2. Find The Bad Ground: Probe the suspected ground wire or contact with the probe tip. If the circuit breaker tripped, this circuit is more than likely a good ground.
3. Testing Trailer Lights: While the tool in DC Voltage mode, clip the auxiliary ground lead to the trailer ground , probe the contacts at the jack and then apply voltage to the probe tip. This lets you check the function and orientation of the connector and trailer lights.
4. Check Continuity: While the tool is in Resistance mode, using the probe tip with chassis is ground or the auxiliary ground lead, continuity can be tested on wires and components attached or disconnected from the vehicle’s electrical system.
5. Activating Component: The component activation function is designed to generate activation signals to the tested components, such as activating lights, motors and other on-board electric equipments.
6. Signal Circuit Testing: Once you extract a DTC from the vehicle and realize that troubleshooting begins with some kind of sensor circuit, there is a quick test you can perform to verify the code. Testing your sensor is easy while using the tool.
7. Voltage & Polarity Testing: While the tool is in DC Voltage mode, contact the probe tip to a POSITIVE circuit. If contact the probe tip to an OPEN circuit, neither of the LED will light.
🎁Package List:
1 × ANCEL PB100 Power Scan Main Unit
1 × BST200 Car Battery Tester
1 × Rugged Blow Molded Case
1 × 20ft. Extension Cable
1 × Probe
1 × Battery Hookup Clips
1 × Cig-a-r-e-tte Lighter Adapter
-
🔔【WIDER TESTING RANGE】:
ANCEL BST200 Battery Cell Tester of automotive works on 12V lead-acid batteries, including regular flooded, AGM flat plate, AGM spiral, and GEL batteries for cars, RV, SUV, motorcycle, boats, light truck, and even golf carts.Gives you an accurate result in merely seconds, such as CCA value, CCA rating, voltage, internal resistance, state of health, and state of charge, based on the rating standard of CCA, CA, MCA, JIS, DIN, IEC, EN and SAE.
-
🏹【FASTER & MORE ACCURATE】:
ANCEL BST200 Automotive Battery Tester helps you to quickly detect battery faults so that you can replace it in time for the warranty period. Whether it’s a hot summer day or a cold winter day, you can choose to test your battery OUT OF VEHICLE or IN VEHICLE, which is convenient and SAVES your TIME and MONEY.
-
📈【DISPLAY OVERALL BATTERIES DATA】:
The Vehicle Battery Tester Tool professionally test your battery, giving you the volt, measured value, rating, SOC and SOH values. What’s more, it will give you accurate advice on your electricity, after the test you will get one of the 5 test results directly: 1️⃣[GOOD BATTERY]2️⃣[GOOD-RECHARGE]3️⃣[CHARGE & RETEST]4️⃣[REPLACE BATTERY]5️⃣[BAD CELL-REPLACE]. Lets you know the exact condition of your battery.
-
🔋【CHECK BATTERY LIFE】:
ANCEL BST200 Battery Analyzer lets you know if your battery is in good condition, has enough power, or needs recharging. The SOC (State of Charge) indicator of battery reflects the remaining capacity of the battery， SOC = 0 (fully discharged), SOC = 100% (fully charged). The SOH (State of Health) indicator reflects the current operating capacity and remaining life of the battery.
-
💯【EASY TO USE & PLUG AND PLAY】:
Instant-on and ready-to-use. BST200 Battery Load Tester has four simple buttons: UP, DOWN, ESC, and ENTER, that are easy to understand and operate, Plug and Play.Easy to read, After properly connecting the Positive(+) and Negative(-) poles with the test cable, the tester can immediately read the voltage value.
-
⚡【What is a PB100 Probe Tester?】
With the PB100 probe tester, you can check voltage and ground signals in a typical DC circuit. However, the kicker is that you can also use it to send voltage and ground signals. It works like a test light that can power circuits or provide a good known ground. This way, you can effectively test components and circuits without having to break out the old alligator clips and jumper wires. You can power or ground a circuit directly through the top of the device.
-
✨【What does it do?】
The PB100 is an essential tool for automobile user. It is needed for testing components on and off the vehicle, checking for the good and bad grounds, testing for continuity and diagnosing circuit failures. For example, you can use it to turn on a blower motor. You can run power window motors, windshield wipers, and even rear window defrosters. If the vehicle owner keeps it in his car he can check system failure on his own way no need to go to technician.